Electronic Transformer
ZXY is a premier electronic transformer manufacturer, delivering high-performance electronic transformer technology engineered for efficient voltage conversion, signal processing, electrical isolation, and high-frequency power switching. Covering a comprehensive lineup—from precise audio and microphone input transformers to high-efficiency toroidal, low-frequency power, and high-frequency switching types—our products are manufactured using premium magnetic cores, high-purity copper windings, and advanced insulation technology. Each electronic transformer delivers exceptional power efficiency, low electromagnetic interference (EMI), superior frequency response, and high dielectric strength. These products are widely used across professional audio equipment, power supply units (PSUs), industrial automation, medical electronics, renewable energy, and telecommunications. Engineered to meet strict safety and performance standards, they ensure reliable power delivery and pristine signal transmission in demanding environments. We also provide customized power ratings, impedance ratios, winding configurations, and mounting packages to meet diverse B2B customer requirements.
Send your inquiry
ZXY-DU18 is a wideband audio isolation transformer in a sealed permalloy alloy housing with DIP through-hole mounting. Two winding variants are available, 1+1:1+1 and 1+1:3.5+3.5. Frequency response is ±0.5 dB from 10 Hz to 100 kHz at 1 % THD against a −6 dB 1 kHz reference, the maximum 50 Hz input level is +13 dBu, and the hi-pot rating is 1,250 V tested at 1 mA for 60 s. The part couples voice and data signals while breaking the ground path between equipment. Outline 38.5 mm by 24.5 mm, 22.0 mm high, on 8 pins in two rows of four at 5.0 mm pitch.
ZXY-B2511 is a cased permalloy audio isolation transformer with two separate 1:1 windings, built for low-frequency signal paths. Both windings measure 110 Ω ±10 % DC resistance and 1.0 H minimum inductance at 1 kHz / 0.3 V, and the turns ratio is held to 1:1 ±2 %. Frequency response stays within ±0.12 dB from 300 Hz to 4 kHz referred to 1 kHz. Insulation resistance is 100 MΩ min at 200 VDC with a 1,250 VDC hi-pot at 1 mA for 60 s between windings. Body 12.0 mm max by 9.3 mm max, 5.8 mm max high, on four SMD gull-wing pins with the PCB land layout defined in the specification.
ZXY-B2111 Audio Isolation Transformer, 1:1 600 Ohm Line Audio Transformer, SMD Potted, 4.6 kV Hi-Pot
ZXY-B2111 is a 1:1 audio isolation transformer on an ED8×11 nickel-steel lamination core, supplied as a fully potted SMD body of 13.8 mm by 10.6 mm and 8.0 mm high. Both windings are 520 turns of 2UEW-F Ø0.04 mm enamel wire, wound on a thickened double-section bobbin with 0.15 mm laminations interleaved and fully stacked, which is what holds the turns ratio to ±1 %. DC resistance is 115 Ω ±10 % on pins 1-3 and on pins 4-6; inductance 1.4 H min at 1 kHz and 0.25 V, parallel resistance 7,500 Ω min. In a 600 Ω system insertion loss is 2 dB max at 2 kHz and return loss 24 dB min from 200 Hz to 4 kHz, with response inside ±0.25 dB. Insulation resistance 100 MΩ min at 200 VDC, hi-pot 4,600 VDC at 1 mA for 60 s.
ZXY-G14 is a compact PCB-mount audio transformer on a G14 pot core in XP95 ferrite, one core set per unit, wound with 0.12 mm self-bonding enamel wire and bonded with 316 anaerobic adhesive. The main winding on pins 2-3 measures at least 420 mH at 10 kHz and 1 V, with a DC resistance of 19 Ω ±10% at 25 °C. Three 0.7 mm pins on a 3.5 mm pitch with 7.0 mm row spacing drop into a standard footprint, and a central M2 x 16 stud with an M2 x 2 nut gives a chassis or bracket fixing. Body 16.3 mm diameter by 13.8 mm high. Part number G2610. Winding, inductance value, base and pin-out are built to your drawing.
ER14.5 is a high-frequency ferrite core transformer for surface-mount power supplies: a NiZn power ferrite core, precision-wound copper windings brought out on terminals 1-3 and 4-6, and an encapsulated case over tin-plated gullwing terminals. The series is declared across 1 Hz to 1 MHz, -45 °C to +125 °C and 30% to 70% relative humidity, with primary voltage from 6 V to 305 V, secondary from 1.8 V to 55 V, DC resistance 2.8 Ω to 82 Ω and 0.02 Ω to 12.8 Ω, and leakage inductance 0.32 µH to 5.8 µH, all at 1 kHz, 0.25 V. Body 15.0 x 12.0 x 7.0 mm maximum. Windings, ratio and footprint are built to the customer's design, so a sample is matched to your schematic rather than chosen from a catalogue.
ZXY2207 is a permalloy audio isolation transformer in a shielded metal can, made in five builds: 600:600 at 1:1 with 6.0 H, 600:600 dual at 1+1 : 1+1 with 14.0 H, 10K:10K at 1:1 with 105 H, 600:10K at 1:4 and 10K:600 at 4:1. All are held to ±2% on ratio and ±15% on DC resistance, isolated to 1250 V AC at 1 mA for 60 s, and rated −40 °C to +85 °C. Six pins on a 4.0 mm grid, footprint 22.0 x 18.3 mm. Data at 25 °C. The windings are tightly coupled on a high-permeability core, so almost all of the flux set up by the primary links the secondary and the coupling coefficient sits close to one. That is what makes the response flat across the band: the bottom of the passband is set by the primary inductance and the top by the leakage inductance. The primary job of the part, though, is the isolation - the two windings share no conductor, so a ground potential difference between two pieces of equipment has no path to travel.
ZXY-CT226A is a precision AC current transformer for PCB mounting: an epoxy-potted body with a Φ5 mm primary bore and two secondary pins, 30 A AC rated input at 50/60 Hz, offered as 1000:1 (GL-CT226A1.0B) with 30 mA AC output or 2000:1 (GL-CT226A2.0B) with 15 mA AC output. Phase error is 5 arc-minutes or better at the stated burden, linearity 0.2% on the 1000:1 build and 0.1% on the 2000:1. Insulation resistance is above 1000 MΩ, the case is UL94-V0, and dielectric withstand is 4 kV at 50 Hz for 1 minute over −40 °C to +70 °C. The primary is the cable or busbar that passes through the bore, not a winding of the part, so the part reads whatever current the conductor carries without being connected into that circuit at all. What comes out of the two pins is a scaled copy, small enough for a metering or protection input to accept directly. That is what makes it usable on a mains conductor: the measuring circuit never touches it.
ZXY-ED12.6-20H is an SMD audio isolation transformer on a permalloy core: a sealed core in a high-gloss tape wrap, a plastic bobbin with the primary on pins 1-5 and the secondary on pins 6-10, and ten formed SMD pins, five to a side. 100 Hz to 20 kHz, turns ratio 1:1 within ±2%, primary inductance 20 H minimum at 1 kHz and 0.3 V, dielectric withstand 1250 V at 1 mA / 60 s. Outline 10.0 mm high, 17.8 mm long and 13.3 mm wide. Data at 25 °C. It sits between two stages of a signal path that must not share a conductor. The isolation keeps a fault or a burn-out on one side away from the output stage on the other, removes the AC mains-frequency interference that travels along the ground, and breaks the common-ground loop that produces hum. Being surface mount, it is placed by the same process as the rest of the board, which is why the 20 H winding is wound on a part this small.
EL14 is a horizontal audio isolation transformer for through-hole PCB mounting: a precision ferrite core, a precision coil wound primary 1-2 and secondary 4-3 under yellow tape insulation, and four pins in two rows underneath the body. Two variants are listed under the model, EI1401 and EI1402, both 1:1 and both rated 1500 V at 1 mA / 60 s. Operating range 300 Hz to 3.4 kHz. Body 16 mm maximum length, 8.5 mm high, pin rows 12 mm apart. Data at 25 °C. The part sits between two circuits that must not share a conductor: it couples the voice or data signal while breaking the earth path, which removes the hum a system picks up when it is grounded at more than one point, and it keeps a fault on one side away from the output stage on the other. Balanced and unbalanced runs both benefit, which is why the same part appears in telephone, biomedical and induction-speaker equipment.
ZXY-EI16 is a microphone transformer in fly-lead form: an EI16 laminated steel core, a coil wound on an insulated bobbin under a yellow tape wrap, and four colour-coded leads instead of PCB pins. Two turns-ratio versions are standard, 1:5 as type B2456 and 1:6 as type B2577, both specified over 50 Hz to 20 kHz and both rated 1500 V at 1 mA / 60 s. Overall 16.5 mm long, 14.5 mm high and 14.5 mm deep. Electrical data at 25 °C. The leads identify the windings at the bench: BLUE and YELLOW on the primary, which is the microphone side, RED and GREEN on the secondary, which is the console side, with the phase end of each winding marked by a dot on the wiring diagram. Because there are no pins the part is wired into a microphone body, a harness or an existing board assembly after the mechanical design is fixed.
ZXY-DU135 is a microphone transformer in flying-lead form: a laminated silicon steel core, a copper winding on a nylon bobbin under an insulation wrap, and four colour-coded leads (BLACK, RED, BLUE, YELLOW) instead of PCB pins. Three turns-ratio versions run in the same body, 1:1.2, 1:2 and 1:5, all specified over 50 Hz to 20 kHz and all rated 1500 V at 1 mA / 60 s. Overall 19.5 mm long, 16.5 mm high and 13.0 mm across, with the core stack 7.0 mm thick. Electrical data at 25 °C. Leads rather than pins means the part is wired into a harness, a microphone body or an existing board assembly after the mechanical design is settled. The isolation breaks the conductive path between two audio circuits while passing the signal, which removes the AC mains interference and the ground-loop hum that appear when equipment is earthed at different points, and it cuts the external interference picked up on both balanced and unbalanced runs.
ZXY DU124 is a microphone transformer in fly-lead form: stacked EI lamination core, precision copper winding under high-dielectric-strength yellow Mylar tape, and four pre-tinned leads with UL AWM style insulation instead of PCB pins. Turns ratio 1:4, 1:7 or 1:12, frequency range 20 Hz to 20 kHz, dielectric withstand 1500 V at 1 mA / 60 s. Body 16.5 mm wide, 12.0 mm deep, 25.0 mm high, leads 40 ± 2 mm. Electrical data at 25 °C. Four leads and no pins means the part is wired rather than placed on a footprint, which is what makes it usable inside a microphone body, on a flying harness, or in a retrofit where the mounting position is already fixed. The isolation breaks the ground connection between two stages while passing the signal, removing the AC hum that appears when equipment sits on different earth potentials, and it reduces interference on both balanced and unbalanced runs.
Huizhou Company Address
Zhixiangyuan Technology Co., Ltd., 5th Floor, Building 4, Xinghe Industrial Park, Zhongkai High tech Zone, Huicheng District, Huizhou City, Guangdong Province
Useful Links
Product
Contact Us
Shenzhen Company Address
Room 202, Yingfei Haocheng Science and Technology Park, Guansheng 5th Road, Luhu Community, Guanhu Street, Longhua District, Shenzhen City, Guangdong Province, China